llvm-svn: 54128

hook for each way in which a result type can be
legalized (promotion, expansion, softening etc),
just use one: ReplaceNodeResults, which returns
a node with exactly the same result types as the
node passed to it, but presumably with a bunch of
custom code behind the scenes.  No change if the
new LegalizeTypes infrastructure is not turned on.

llvm-svn: 53137

and better control the abstraction.  Rename the type
to MVT.  To update out-of-tree patches, the main
thing to do is to rename MVT::ValueType to MVT, and
rewrite expressions like MVT::getSizeInBits(VT) in
the form VT.getSizeInBits().  Use VT.getSimpleVT()
to extract a MVT::SimpleValueType for use in switch
statements (you will get an assert failure if VT is
an extended value type - these shouldn't exist after
type legalization).
This results in a small speedup of codegen and no
new testsuite failures (x86-64 linux).

llvm-svn: 52044

memcpy/memset expansion. It was a bug for the SVOffset value
to be used in the actual address calculations.

llvm-svn: 50359

memory intrinsic expansion code.

llvm-svn: 49666

on any current target and aren't optimized in DAGCombiner. Instead
of using intermediate nodes, expand the operations, choosing between
simple loads/stores, target-specific code, and library calls,
immediately.

Previously, the code to emit optimized code for these operations
was only used at initial SelectionDAG construction time; now it is
used at all times. This fixes some cases where rep;movs was being
used for small copies where simple loads/stores would be better.

This also cleans up code that checks for alignments less than 4;
let the targets make that decision instead of doing it in
target-independent code. This allows x86 to use rep;movs in
low-alignment cases.

Also, this fixes a bug that resulted in the use of rep;stos for
memsets of 0 with non-constant memory size when the alignment was
at least 4. It's better to use the library in this case, which
can be significantly faster when the size is large.

This also preserves more SourceValue information when memory
intrinsics are lowered into simple loads/stores.

llvm-svn: 49572

to pass the mask APInt by value, not by reference. 

llvm-svn: 47096

Add an overload that supports the uint64_t interface for use by clients
that haven't been updated yet.

llvm-svn: 47039

llvm-svn: 46723

Even though InsertAtEndOfBasicBlock is an ugly hack it still deserves a proper name. Rename it to EmitInstrWithCustomInserter since it does not necessarily insert
instruction at the end.

llvm-svn: 46562

llvm-svn: 45418

llvm-svn: 44380

1) Change the interface to TargetLowering::ExpandOperationResult to 
   take and return entire NODES that need a result expanded, not just
   the value.  This allows us to handle things like READCYCLECOUNTER,
   which returns two values.
2) Implement (extremely limited) support in LegalizeDAG::ExpandOp for MERGE_VALUES.
3) Reimplement custom lowering in LegalizeDAGTypes in terms of the new
   ExpandOperationResult.  This makes the result simpler and fully 
   general.
4) Implement (fully general) expand support for MERGE_VALUES in LegalizeDAGTypes.
5) Implement ExpandOperationResult support for ARM f64->i64 bitconvert and ARM
   i64 shifts, allowing them to work with LegalizeDAGTypes.
6) Implement ExpandOperationResult support for X86 READCYCLECOUNTER and FP_TO_SINT,
   allowing them to work with LegalizeDAGTypes.

LegalizeDAGTypes now passes several more X86 codegen tests when enabled and when
type legalization in LegalizeDAG is ifdef'd out.

llvm-svn: 44300

Thanks for the suggestions Bill :-)

llvm-svn: 43742

and by restructuring the X86 version.

New I just have to move this to a common place :-)

llvm-svn: 43554

llvm-svn: 43234

llvm-svn: 43176

use ISD::{S,U}DIVREM and ISD::{S,U}MUL_HIO. Move the lowering code
associated with these operators into target-independent in LegalizeDAG.cpp
and TargetLowering.cpp.

llvm-svn: 42762

init_trampoline.  There is now only one
trampoline intrinsic.

llvm-svn: 41841

llvm-svn: 40757

still under discussion.

llvm-svn: 40549

TargetLowering to SelectionDAG so that they have more convenient
access to the current DAG, in preparation for the ValueType routines
being changed from standalone functions to members of SelectionDAG for
the pre-legalize vector type changes.

llvm-svn: 37704

llvm-svn: 37659

in the order lod;lod;lod;sto;sto;sto which means the load-store optimizer
has a better chance of producing ldm/stm.  Ideally you would get cooperation
from the RA as well but this is not there yet.

llvm-svn: 37179

llvm-svn: 36506

llvm-svn: 36324

llvm-svn: 35846

llvm-svn: 35840

flags (ARMISD::CMPNZ) and comparisons that use all flags (ARMISD::CMP).
- Defines the instructions: TST, TEQ (ARM) and TST (Thumb).

llvm-svn: 35573

llvm-svn: 35521

llvm-svn: 35406

not just the first letter.  No functionality change.

llvm-svn: 35322

llvm-svn: 35245

instructions (that would have to be split later)

llvm-svn: 35227

llvm-svn: 35196

llvm-svn: 35122

llvm-svn: 35075

        .set PCRELV0, (LJTI1_0_0-(LPCRELL0+4))
LPCRELL0:
        add r1, pc, #PCRELV0
This is not legal since add r1, pc, #c requires the constant be a multiple of 4.
Do the following instead:
        .set PCRELV0, (LJTI1_0_0-(LPCRELL0+4))
LPCRELL0:
        mov r1, #PCRELV0
        add r1, pc

- In thumb mode, it's not possible to use .set generate a pc relative stub
  address. The stub is ARM code which is in a different section from the thumb
  code. Load the value from a constpool instead.
- Some asm printing clean up.

llvm-svn: 33664

llvm-svn: 33353