llvm-svn: 35001

llvm-svn: 34996

llvm-svn: 34992

llvm-svn: 34984

llvm-svn: 34939

scalarrepl things down to elements, but mem2reg can't promote elements that
are memset/memcpy'd.  Until then, the code is disabled "0 &&".

llvm-svn: 34924

llvm-svn: 34920

define i64 @test(i64 %A, i32 %B) {
        %tmp12 = zext i32 %B to i64             ; <i64> [#uses=1]
        %tmp3 = shl i64 %tmp12, 32              ; <i64> [#uses=1]
        %tmp5 = add i64 %tmp3, %A               ; <i64> [#uses=1]
        %tmp6 = and i64 %tmp5, 123              ; <i64> [#uses=1]
        ret i64 %tmp6
}

into:

define i64 @test(i64 %A, i32 %B) {
        %tmp6 = and i64 %A, 123         ; <i64> [#uses=1]
        ret i64 %tmp6
}

This implements Transforms/InstCombine/add2.ll:test1

llvm-svn: 34919

llvm-svn: 34917

llvm-svn: 34914

llvm-svn: 34904

llvm-svn: 34902

up simplifycfg by 20%

llvm-svn: 34901

would scan the entire loop body, then scan all users of instructions in the
loop, looking for users outside the loop.  Now, since we know that the
loop is in LCSSA form, we know that any users outside the loop will be LCSSA
phi nodes.  Just scan them.

This speeds up indvars significantly.

llvm-svn: 34898

This makes -indvars require and use LCSSA, updating it as appropriate.

llvm-svn: 34896

llvm-svn: 34891

the order that instcombine processed instructions in the testcase.  The end
result is that instcombine finished with:

define i16 @test1(i16 %a) {
        %tmp = zext i16 %a to i32               ; <i32> [#uses=2]
        %tmp21 = lshr i32 %tmp, 8               ; <i32> [#uses=1]
        %tmp5 = shl i32 %tmp, 8         ; <i32> [#uses=1]
        %tmp.upgrd.32 = or i32 %tmp21, %tmp5            ; <i32> [#uses=1]
        %tmp.upgrd.3 = trunc i32 %tmp.upgrd.32 to i16           ; <i16> [#uses=1]
        ret i16 %tmp.upgrd.3
}

which can't get matched as a bswap.

This patch makes instcombine more sophisticated about removing truncating
casts, allowing it to turn this into:

define i16 @test2(i16 %a) {
        %tmp211 = lshr i16 %a, 8
        %tmp52 = shl i16 %a, 8
        %tmp.upgrd.323 = or i16 %tmp211, %tmp52
        ret i16 %tmp.upgrd.323
}

which then matches as bswap.  This fixes bswap.ll and implements
InstCombine/cast2.ll:test[12].  This also implements cast elimination of
add/sub.

llvm-svn: 34870

llvm-svn: 34868

finish without combining something it is capable of.

llvm-svn: 34865

llvm-svn: 34863

Replace expensive getZExtValue() == 0 calls with isZero() calls.

llvm-svn: 34861

llvm-svn: 34860

llvm-svn: 34859

llvm-svn: 34858

llvm-svn: 34856

2. Make sure debug output of APInt values is safe for all bit widths.

llvm-svn: 34855

llvm-svn: 34854

llvm-svn: 34853

a value from the worklist required scanning the entire worklist to remove all
entries.  We now use a combination map+vector to prevent duplicates from
happening and prevent the scan.  This speeds up instcombine on a large file
from the llvm-gcc bootstrap from 189.7s to 4.84s in a debug build and from
5.04s to 1.37s in a release build.

llvm-svn: 34848

llvm-svn: 34846

llvm-svn: 34832

llvm-svn: 34822

Constant::isNullValue() in situations where it is possible.

llvm-svn: 34821

using isNullValue() instead of getZExtValue() == 0.

llvm-svn: 34815

assert if the ConstantInt's value is large.

llvm-svn: 34814

bit width of the ConstantInt being converted.

llvm-svn: 34810

This caused a warning for construction with -1. Avoid the warning by using
-1ULL instead.

llvm-svn: 34796

are not needed as the results are the same with or without it.

Patch by Nicholas Lewycky.

llvm-svn: 34782

Adjust to changes in ConstantRange interface.

llvm-svn: 34762

Remove ConstantInt from ConstantRange interface and adjust its users to
compensate.

llvm-svn: 34758