The tool reports verbose output for the DWARF debug location coverage.
The llvm-locstats for each variable or formal parameter DIE computes what
percentage from the code section bytes, where it is in scope, it has
location description. The line 0 shows the number (and the percentage) of
DIEs with no location information, but the line 100 shows the number (and
the percentage) of DIEs where there is location information in all code
section bytes (where the variable or parameter is in the scope). The line
50..59 shows the number (and the percentage) of DIEs where the location
information is in between 50 and 59 percentage of its scope covered.

The tool will be very useful for tracking improvements regarding the
"debugging optimized code" support with LLVM ecosystem.

Differential Revision: https://reviews.llvm.org/D66526

llvm-svn: 371520

Add a mode in which profile read errors are not immediately treated as
fatal. In this mode, merging makes forward progress and reports failure
only if no inputs can be read.

Differential Revision: https://reviews.llvm.org/D66985

llvm-svn: 370827

Summary:
Commit r366897 introduced the possibility to set a variable from an
expression, such as [[#VAR2:VAR1+3]]. While introducing this feature, it
introduced extra logic to allow using such a variable on the same line
later on. Unfortunately that extra logic is flawed as it relies on a
mapping from variable to expression defining it when the mapping is from
variable definition to expression. This flaw causes among other issues
PR42896.

This commit avoids the problem by forbidding all use of a variable
defined on the same line, and removes the now useless logic. Redesign
will be done in a later commit because it will require some amount of
refactoring first for the solution to be clean. One example is the need
for some sort of transaction mechanism to set a variable temporarily and
from an expression and rollback if the CHECK pattern does not match so
that diagnostics show the right variable values.

Reviewers: jhenderson, chandlerc, jdenny, probinson, grimar, arichardson, rnk

Subscribers: JonChesterfield, rogfer01, hfinkel, kristina, rnk, tra, arichardson, grimar, dblaikie, probinson, llvm-commits, hiraditya

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D66141

llvm-svn: 370663

--add-symbol to be specified with --new-symbol-visibility

llvm-svn: 370458

It was causing some errors like:

Encoding error:
'ascii' codec can't decode byte 0xe2 in position 341: ordinal not in range(128)
The full traceback has been saved in /tmp/sphinx-err-y2fq4dtb.log, if you want to report the issue to the developers.

llvm-svn: 369644

Summary:
Linking between markdown and rst files is currently not supported very well, e.g. the current llvm-addr2line docs [1] link to "llvm-symbolizer" instead of "llvm-symbolizer.html". This is weirdly broken in different ways depending on which versions of sphinx and recommonmark are being used, so workaround the bug by using rst everywhere.

[1] http://llvm.org/docs/CommandGuide/llvm-addr2line.html

Reviewers: jhenderson

Reviewed By: jhenderson

Subscribers: lebedev.ri, llvm-commits

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D66305

llvm-svn: 369553

add-symbol

Reviewers: Maskray, rupprecht

Differential Revision: https://reviews.llvm.org/D65891

llvm-svn: 368982

llvm-svn: 368473

Summary: Addresses https://bugs.llvm.org/show_bug.cgi?id=42383

Reviewers: jhenderson, alexshap, rupprecht

Reviewed By: jhenderson

Subscribers: wolfgangp, jakehehrlich, llvm-commits

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D65384

llvm-svn: 368464

Flag -show-encoding enables the printing of instruction encodings as part of the
the instruction info view.

Example (with flags -mtriple=x86_64--  -mcpu=btver2):

Instruction Info:
[1]: #uOps
[2]: Latency
[3]: RThroughput
[4]: MayLoad
[5]: MayStore
[6]: HasSideEffects (U)
[7]: Encoding Size

[1]    [2]    [3]    [4]    [5]    [6]    [7]    Encodings:     Instructions:
 1      2     1.00                         4     c5 f0 59 d0    vmulps   %xmm0, %xmm1, %xmm2
 1      4     1.00                         4     c5 eb 7c da    vhaddps  %xmm2, %xmm2, %xmm3
 1      4     1.00                         4     c5 e3 7c e3    vhaddps  %xmm3, %xmm3, %xmm4

In this example, column Encoding Size is the size in bytes of the instruction
encoding. Column Encodings reports the actual instruction encodings as byte
sequences in hex (objdump style).

The computation of encodings is done by a utility class named mca::CodeEmitter.

In future, I plan to expose the CodeEmitter to the instruction builder, so that
information about instruction encoding sizes can be used by the simulator. That
would be a first step towards simulating the throughput from the decoders in the
hardware frontend.

Differential Revision: https://reviews.llvm.org/D65948

llvm-svn: 368432

Summary:
The information for -info -thin -create -replace and -segalign flags are added to llvm-lipo.rst

Test Plan:

Reviewers: smeenai, alexshap, compnerd, mtrent

Subscribers: llvm-commits

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D65676

llvm-svn: 368235

Reviewers: jhenderson, grimar, rupprecht

Differential Revision: https://reviews.llvm.org/D65313

llvm-svn: 367942

Also clarify the meaning of 'Block RThroughput' and 'RThroughput'.

llvm-svn: 367853

Addresses PR42864.

llvm-svn: 367689

[MCA] Add support for printing immedate values as hex. Also enable lexing of masm binary and hex literals.

This patch adds a new llvm-mca flag named -print-imm-hex.

By default, the instruction printer prints immediate operands as decimals. Flag
-print-imm-hex enables the instruction printer to print those operands in hex.

This patch also adds support for MASM binary and hex literal numbers (example
0FFh, 101b).
Added tests to verify the behavior of the new flag. Tests also verify that masm
numeric literal operands are now recognized.

Differential Revision: https://reviews.llvm.org/D65588

llvm-svn: 367671

This patch enables support for --add-section=... option for COFF objects.

Differential Revision: https://reviews.llvm.org/D65040

llvm-svn: 367130

Summary:
This patch is part of a patch series to add support for FileCheck
numeric expressions. This specific patch lift the restriction for a
numeric expression to either be a variable definition or a numeric
expression to try to match.

This commit allows a numeric variable to be set to the result of the
evaluation of a numeric expression after it has been matched
successfully. When it happens, the variable is allowed to be used on
the same line since its value is known at match time.

It also makes use of this possibility to reuse the parsing code to
parse a command-line definition by crafting a mirror string of the
-D option with the equal sign replaced by a colon sign, e.g. for option
'-D#NUMVAL=10' it creates the string
'-D#NUMVAL=10 (parsed as [[#NUMVAL:10]])' where the numeric expression
is parsed to define NUMVAL. This result in a few tests needing updating
for the location diagnostics on top of the tests for the new feature.

It also enables empty numeric expression which match any number without
defining a variable. This is done here rather than in commit #5 of the
patch series because it requires to dissociate automatic regex insertion
in RegExStr from variable definition which would make commit #5 even
bigger than it already is.

Copyright:
    - Linaro (changes up to diff 183612 of revision D55940)
    - GraphCore (changes in later versions of revision D55940 and
                 in new revision created off D55940)

Reviewers: jhenderson, chandlerc, jdenny, probinson, grimar, arichardson, rnk

Subscribers: hiraditya, llvm-commits, probinson, dblaikie, grimar, arichardson, tra, rnk, kristina, hfinkel, rogfer01, JonChesterfield

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D60388

> llvm-svn: 366860

llvm-svn: 366897

This reverts commit 1b059775.

llvm-svn: 366872

Summary:
This patch is part of a patch series to add support for FileCheck
numeric expressions. This specific patch lift the restriction for a
numeric expression to either be a variable definition or a numeric
expression to try to match.

This commit allows a numeric variable to be set to the result of the
evaluation of a numeric expression after it has been matched
successfully. When it happens, the variable is allowed to be used on
the same line since its value is known at match time.

It also makes use of this possibility to reuse the parsing code to
parse a command-line definition by crafting a mirror string of the
-D option with the equal sign replaced by a colon sign, e.g. for option
'-D#NUMVAL=10' it creates the string
'-D#NUMVAL=10 (parsed as [[#NUMVAL:10]])' where the numeric expression
is parsed to define NUMVAL. This result in a few tests needing updating
for the location diagnostics on top of the tests for the new feature.

It also enables empty numeric expression which match any number without
defining a variable. This is done here rather than in commit #5 of the
patch series because it requires to dissociate automatic regex insertion
in RegExStr from variable definition which would make commit #5 even
bigger than it already is.

Copyright:
    - Linaro (changes up to diff 183612 of revision D55940)
    - GraphCore (changes in later versions of revision D55940 and
                 in new revision created off D55940)

Reviewers: jhenderson, chandlerc, jdenny, probinson, grimar, arichardson, rnk

Subscribers: hiraditya, llvm-commits, probinson, dblaikie, grimar, arichardson, tra, rnk, kristina, hfinkel, rogfer01, JonChesterfield

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D60388

llvm-svn: 366860

This reverts r365889 (git commit 60c81354)

llvm-svn: 366219

llvm-svn: 366080

Summary:
This patch is part of a patch series to add support for FileCheck
numeric expressions. This specific patch extend numeric expression to
support an arbitrary number of operands, either variable or literals.

Copyright:
    - Linaro (changes up to diff 183612 of revision D55940)
    - GraphCore (changes in later versions of revision D55940 and
                 in new revision created off D55940)

Reviewers: jhenderson, chandlerc, jdenny, probinson, grimar, arichardson, rnk

Subscribers: hiraditya, llvm-commits, probinson, dblaikie, grimar, arichardson, tra, rnk, kristina, hfinkel, rogfer01, JonChesterfield

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D60387

llvm-svn: 366001

Summary: This moves away from defaulting to a.out and uses stdin only if stdin has a file redirected to it. This has been discussed on the llvm-dev mailing list [[ https://lists.llvm.org/pipermail/llvm-dev/2019-July/133642.html | here ]].

Reviewers: jhenderson, rupprecht, MaskRay, chrisjackson

Reviewed By: jhenderson, MaskRay

Subscribers: llvm-commits

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D64290

llvm-svn: 365889

llvm-svn: 365630

llvm-svn: 365603

llvm-svn: 365489

llvm-svn: 365474

In particular, the --debug-syms switch really doesn't have anything to
do with debuggers, so I've updated the document accordingly.

llvm-svn: 365461

Some of the wording in the doc (taken largely from the help text), was a
little imprecise in some cases, so this patch makes it a little more
precise.

Reviewed by: JDevlieghere, probinson

Differential Revision: https://reviews.llvm.org/D64332

llvm-svn: 365451

llvm-svn: 365335

Similar to `FILECHECK_OPTS` for FileCheck, `LIT_OPTS` makes it easy to
adjust lit behavior when running the test suite via ninja.  For
example:

```
$ LIT_OPTS='--time-tests -vv --filter=threadprivate' \
  ninja check-clang-openmp
```

Reviewed By: probinson

Differential Revision: https://reviews.llvm.org/D64135

llvm-svn: 365313

We briefly referred to being able to specify --target=binary without
explaining what binary input/output meant. This change adds a section on
this.

Reviewed by: MaskRay, abrachet

Differential Revision: https://reviews.llvm.org/D64245

llvm-svn: 365312

--section-data, --section-relocations and --section-symbols have no
effect for GNU style ouput. This patch changes the docs to point this
out, as it has caught me out on a couple of occasions.

See also https://bugs.llvm.org/show_bug.cgi?id=42522.

llvm-svn: 365221

llvm-svn: 365187

Summary: Changes "see also" links to use :manpage: instead of plain text or the form `name|name` which was being treated literally, not as a link.

Reviewers: jhenderson, rupprecht

Reviewed By: jhenderson

Subscribers: llvm-commits

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D63970

llvm-svn: 365159

The --show-children option description describes what it does, and
references the =<offset> parameter of section dump switches. I don't
think it needs to be explained again in the documentation of the
section dump switches too.

Reviewed by: JDevlieghere

Differential Revision: https://reviews.llvm.org/D64132

llvm-svn: 365115

Summary: Removed excess new lines from documentations. As far as I can tell, it seems as though restructured text is agnostic to new lines, the use of new lines was inconsistent and had no effect on how the files were being displayed.

Reviewers: jhenderson, rupprecht, JDevlieghere

Reviewed By: jhenderson

Subscribers: llvm-commits

Tags: #llvm

Differential Revision: https://reviews.llvm.org/D63971

llvm-svn: 365105

This patch addresses https://bugs.llvm.org/show_bug.cgi?id=42183 by replacing
the stub markdown doc for llvm-objcopy with a full one describing the current
options available in llvm-objcopy.

Reviewed by: jakehehrlich, MaskRay

Differential Revision: https://reviews.llvm.org/D63820

llvm-svn: 365042

This was accidentally missed when committing r364800.

llvm-svn: 364918

Previously, the llvm-readelf documentation was essentially just a list
of differences to llvm-readobj. Since llvm-readelf is the more likely
goto tool for many people migrating to the LLVM toolchain, it seems like
it would be helpful to document all the switches in the llvm-readelf
document too. This change expands the options listed accordingly.
Additionally, they are unlikely to care what the differences are to
llvm-readobj, since they won't be familiar with the latter as there is
no GNU equivalent, so this change moves the "differences" section to
llvm-readobj's documentation.

Reviewed by: peter.smith

Differential Revision: https://reviews.llvm.org/D63826

llvm-svn: 364800